Sandy Wills

 Real Estate Glossary

Real Estate Glossary
Our glossary is the largest dictionary of real estate and construction terms on the Internet with almost 10,000 definitions.



 
Ba - Bal - Bas - Be - Ben - Bi - Bl - Bo - Bor - Br - Bu - Bun


Fungicide made of a combination of copper sulfate, lime and water.

An edge or dividing line.

To make a hole by drilling.

Lock with a bolt, which slides into the receptacle in the door jamb when the key is turned.

Holder for the boring bit used to bore holes in metal. The chuck of the lathe grabs on to the shaft, which holds the bar. The boring bar is placed at a right angle to the arbor and, when the arbor is rotated, the bit in the boring bar cuts the circle into the metal. The boring bar in the arbor is slid to change the space between the cutting tool and the arbor, which adjusts the size of the circle.

A jig maintains the needed placement between a drill and the material so that the hole is properly aligned.

Record of the information gained about the soil, which was removed from an excavation site.

Soil analysis taken by boring holes into the ground to remove samples.

A section of a city having authority over local matters.

Material used for grading, usually sand or gravel. Borrow Pit A hole at a site where soil has been excavated for use elsewhere. Also called a borrow site.

A hole at a site where soil has been excavated for use elsewhere. Also called a borrow pit.

Liabilities assumed by a borrower; lose of financial ability to repay the loan, rising interest rates (adjustable rate loan) make the payments unaffordable, loan value may exceed the value of the security, etc.

1. Stone which is put into place to be carved at a later date.
2. Projecting formation of rock.
3. Projecting pipe connector that is welded onto a large diameter length of pipe to be connected to a smaller pipe, etc.

Type of roofing where shingles butt tightly against each other at the hip with alternating shingle courses lapping over the edges of the opposing shingles. Also called a Boston Ridge.

Type of roofing where shingles butt tightly against each other at the hip with alternating shingle courses lapping over the edges of the opposing shingles. Also called a Boston Hip.

Guest accommodations offered by some marinas to mariners, similar to motels to motorists.

Lowest structural part of a truss.

Also called a sole plate, this is the board on which the bottoms of the wall framing studs stand.

Land adjacent to a body of water that can also be part of a flood plain or land at the bottom of a valley or glen, which is usually fertile as top soil.

Extremely large rock.

A tree lined street, sometimes constructed with a landscaped median.

Dividing line between two adjacent properties.

Warping of a board or plywood panel so that it is bent and not flat.

Device, which consists of two legs, joined together with a hinged joint that is used for drawing circles. The pointed leg is held in place and the leg, which holds a pencil, or pen is rotated around to draw a circle.

Similar to a compass, a bow divider is used for measuring dimensions. The distance between the pointed ends of both legs can be adjusted and set at the needed dimension for measuring. Once the bow compass is set at a certain measurement, it can transfer those dimensions to another surface.

Window, divided into three sections, that curves outward in an arc, extending the window area out from the wall, so that it gives a room a larger appearance. Since they are supported from the wall or floor and usually don't extend to the roof line, they need their own roof projection from the wall. Ready made bay windows come in pre-assembled components that are easily installed into a wall opening. Also called a bay window.

Beam, girder, or truss with the top portion being in the shape of a bow and the bottom portion being straight across and connecting both ends of the top portion.

Defect that has a poorly covered section joining two well painted sections.

1. Container.
2. Wall opening that accepts an open shutter.
3. Enclosure for electrical connections.
4. To pour paint from container to container so that it mixes well.

Hollow structure constructed of separate structural members connection by their length with intermediate braces between the members.

Supporting a downward load, this is a hollow column consisting of individual structure members in a vertical position.

Construction method where vertical siding is attached to a horizontal framing structure and is often found in agricultural buildings.

Two pieces that have alternating straight finger cuts in their edges and glued into interlocking position to form a very strong joint.

Roof cornice which is enclosed and on the edge.

Flat-headed, thick shanked nail, which is used on thin material in place of larger nails.

Type of sill plate. There are headers, which are nailed to, and encompass joist ends.

Also called a box-end wrench and designed to fit one size nut. The end that fits over and grips the nut is an enclosed circle.

Return to Top

Our glossary is the largest dictionary of real estate and construction terms on the Internet with almost 10,000 definitions.

Sandy Wills
RE/MAX Town Center
19873 Century Boulevard Unit 220
Germantown, MD 20874
Office: 301-540-2232
Cell: 301-873-1474
Direct: 301-428-9300