A flexible series of joined interlocking links, usually metal, used to pull or confine or to transmit power.

A masonry wall that is partially held together by use of an iron bar or chain.

The safety covering that is used over a power-transmitting chain.

Hoist that uses gearing to mechanically lift a load. The gearing is attached to a drum, which has a hook and chain attached. After the load is hooked by the chain, the drum is turned by the gearing, which winds the chain onto the drum, lifting the load.

Official record, detailing ownership history of a piece of property.

Series of welds, alternating from one side of a joint to the other, that run along the length of the joint.

Connection at the edge of a chain link fence, which is twisted and cut wire.

Interlocking heavy lengths of wire that are stretched between metal poles.

Connection at the edge of a chain link fence, which is made of looped wire.

Used to operate a manual valve in a fluid system, this close looped chain is around the teeth on the outside of the wheel which turns the valve and is long enough to be reached by a worker several feet below the valve. The valve is opened, closed and adjusted by someone pulling on one side of the chain loop or the other in a pulley-like motion.

Hand held power made up of a chain with sharp rotating teeth around a flat metal arm, which is used to cut wood and lumber.

Pipe vise that has a lower jaw and a chain passing around the upper circumference of a pipe. Servicing the same function as the upper vise jaw, it is held in slots and can be tightened to hold the pipe.

Pipe wrench made of a length of chain, which is permanently attached to a handle at one end with the other end secured at various places on the handle. For gripping, the chain is looped around the pipe.

Bent metal device which holds rebar elevated in the center, rather than on the bottom of the pour, when cement is poured.

Decorative, horizontal, molding trim installed on a wall 32 inches from the floor.

Soft limestone.

Box which hold chalk and string on a reel which, when withdrawn, becomes coated with chalk. The string is then stretch from one point to another and then "snapped" to make a line of chalk to mark the distance.

Pigment particles released as aging and deterioration of paint occurs, forming a fine powder on the surface.

Paint that oxidizes to form a surface powder, which is then washed off, along with accumulated dirt, leaving the surface clean.

Straight line that is made when a chalk-covered string is snapped against a surface.

A room in a house. Any enclosed space.

Beveled edge or corner, especially one cut on a 45-degree angle.

Concept used in valuing real property that conditions may be altered requiring a revised estimate of market value; for example, deterioration of property or capital improvements.

Adjustment schedule of an adjustable rate mortgage.

Any modification of a construction contract, which is signed by the owner, the architect and the contractor. This would authorize a change in work, the amount of the contract or a change in the contract time.

The switching, by a real estate company, from one accounting method to another.

1. Decorative molding with a concave groove.
2. Groove or flute.
3. Metal structural shape whose cross section is letter C shaped, which is used to support installations such as door headers, windows, etc.
4. A radio frequency.

Also referred to as a bond beam block, rebar can be mortared into the channel or groove of this concrete masonry unit to strengthen its installation.

Tray that uses a solid, one-piece bottom with side rails to support electrical cables where there are many run next to one another.

Metal structural shape whose cross section is letter C shaped, which is used to support installations such as door headers, windows, cable tray support and piping support.

Type of bankruptcy filing, a provision of the 1978 Bankruptcy Reform Act, which provides for a person's property to be divided among creditors to satisfy unpaid debts.

Type of bankruptcy filing allowing restructuring and reorganization of existing debts which is used most often by businesses. Creditors must vote on a debt-paying plan and a judge must approve.

Type of bankruptcy filing in which a person's obligations are paid back within a three year period, allowing the obligated party to pay off debts without liquidating assets.

Credit standard judging the borrower's historical record of paying loans and is among the other considerations of the credit worthiness of the borrower.

Form of carbon, which is created when organic substances are burned without air. Useful where steady long-term heat is desired because of its slow, even burning ability.

1. To add electrical energy to a storage medium.
2. To purchase on credit.
3. To load a mixer.
4. To fill.
5. To place material in a furnace.

1. The shielded vertical shaft that houses pipes, drains, ducts, and flues.
2. A trench or groove.
3. To work decorative patterns into a metal surface.

The wall that surrounds a space through which electrical wiring is run. The interior space is called a chase.

A deep crack in the earth's surface. A wide divergence of feelings or interests.

The structural framework supporting the body of a vehicle, cabinet, etc.

Limestone gravel

Limestone that has a coarse finish.

Portable property, tangible or otherwise, except real estate.

Lien on personal property that is used as collateral for a loan.

Interests and property directly connected with real estate, such as leases, fixtures, etc.

1. A sudden stop or abrupt halt.
2. A restraint or control.
3. A written order to a bank to pay a stated amount of money from one's account.
4. Separation that runs along the grains and across the annual rings in a piece of wood.

Paint surface defect that consists of a square pattern of small cracks.

Also called meeting rails, they are the top horizontal sash member of the bottom window and the bottom horizontal sash member of the top window in a double hung window that mate together tightly when closed, permitting no air passage between the sashes.

Valve permitting flow in a single direction.

Either of two sides of an object, such as a door jamb or the jaws of a vise.

A chamfer cut along the wide part of a board end, allowing the board to fit securely against another framing member at an angle, like at the end of a hip rafter.

A side of an object.

Substance used in or obtained by a chemical process.

A material's ability to withstand change from chemical contact.

Paint can lip which holds the can lid fastened.

Vent that conducts smoke and combustion products through the roof, away from the source of combustion, such as a furnace or fireplace.

The back wall or lining of a furnace, chimney or fireplace.

Concrete cap surrounding the top of the chimney brick and protects the masonry from the elements.

The peaked projection that is built adjacent to a chimney for the purpose of redirecting water away from the chimney.

The upward flow through a channel that is named after the way hot air rises through a chimney.

Inside passage of a chimney that channels smoke and heat to the outside.

Short pipe at the top of a chimney, which increases ventilation to the fireplace to reduce smoke.

Commonly used in the making of bathroom fixtures, this material is impervious to water. It is relatively brittle and subject to cracking.

Fine clay paint pigment that is resistant to abrasion.

Also called Tung Oil or Japanese wood oil this drying oil is taken from the seed kernels of the Tung tree and is used in making wood finishes.

A narrow opening; a crack; a fissure.

Board made of wood chips, which are glued together under pressure.

Hammer that is used to remove scale or paint from a metal surface or slag from a weld. It's steel head is pointed on one end and tapered to a horizontal edge on the other.

Finely crushed rock spread, in a layer, over an asphalt oil base after which is rolled smooth.

Flat bar shaped tool, made of steel, which has a handle on one end and the other end sharpened to a wedge. Chisels are made for cutting, wood, metal, stone and masonry.

A metal cutting chisel which incorporates a striking surface and handle with the shank of the chisel. The length of the chisel is wedge shaped for about a third of the way, tapering down to a hardened cutting edge. Hammers are used to strike a cold chisel.

Used on wood, the teeth and spaces between the teeth of the cutting blade are made to cross cut and rip cut. Most often used for rough carpentry such as framing, the cuts are not very smooth.

Wood cutting chisel, which can be used by hand for shaving or hit with a mallet for heavier cutting.

Plastic material with a higher pressure rating and a higher thermal operating ability at any temperature than Polyvinyl Chloride (PVC) and is used for pipe and fittings.